Clean presets with new reverbs

Discussion in 'Preset Exchange' started by Jace Nuzback, Feb 15, 2018.

  1. Jace Nuzback

    Jace Nuzback Senior Member

    Joined:
    Apr 9, 2017
    Messages:
    1,299
    Likes Received:
    890
    Trophy Points:
    113
    Occupation:
    Product Specialist Atomic Amps
    Home Page:
    Here's 3 clean presets using the two new reverbs Cavern and Plate as well as the newly enhanced Spring 2.
    These were made with vintage output humbuckers.
    They don't have much bass in them.
    If you play single coils, you'll likely want to boost the bass.
    The Deluxe amp model and cab is the same in each.
    Just with different reverbs.
    The compressor is ON for each at the lowest possible settings.
    I tried to make them as transparent as possible while still controlling the transients.
    You'll notice that the reverbs react to the signal differently if you bypass the compressor.
     

    Attached Files:

    Corey S, LHC77, cragginshred and 2 others like this.
  2. flcmcya

    flcmcya Senior Member

    Joined:
    Dec 20, 2016
    Messages:
    229
    Likes Received:
    86
    Trophy Points:
    28
    Thanks buddy!
     
  3. mollydyer

    mollydyer Senior Member

    Joined:
    May 29, 2017
    Messages:
    345
    Likes Received:
    167
    Trophy Points:
    43
    Thanks Jace!
     
  4. John Alexander

    John Alexander New Member

    Joined:
    Nov 28, 2017
    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    1
    Occupation:
    Musician
    Location:
    San Diego California
    ...yes...thanks, Jace!
     
  5. Kyle

    Kyle Active Member

    Joined:
    Jan 14, 2018
    Messages:
    33
    Likes Received:
    11
    Trophy Points:
    8
    Location:
    Guelph, Canada
    awesome. checking these out today
     
  6. slateboy

    slateboy Senior Member

    Joined:
    Dec 20, 2016
    Messages:
    428
    Likes Received:
    227
    Trophy Points:
    43
    Location:
    uk
    Home Page:
    Something i asked, which i think got lost in the recent website hiccup-
    What is the outcome if we attempt to load these presets into an AA running the older firmware?
     
    Earthwine and Patlem like this.
  7. Earthwine

    Earthwine New Member

    Joined:
    Jan 28, 2018
    Messages:
    1
    Likes Received:
    0
    Trophy Points:
    1
    Thanks
    Thanks!
     
  8. cragginshred

    cragginshred Well-Known Member

    Joined:
    Mar 22, 2018
    Messages:
    103
    Likes Received:
    28
    Trophy Points:
    28
    Occupation:
    Physical therpist assistant
    Location:
    Tuolumne Ca.
    Thank you!! I will try them tonight
     
  9. Cristian

    Cristian New Member

    Joined:
    May 13, 2018
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    1
    Occupation:
    Electronic Engineer
    Location:
    Chile
    Thanks Jace !
     
  10. rey

    rey New Member

    Joined:
    Apr 17, 2017
    Messages:
    1
    Likes Received:
    0
    Trophy Points:
    1
    Can you improve the Reverb quality in a future firmware? They are terrible and have very poor quality ‍
     
  11. Quadfire

    Quadfire Well-Known Member

    Joined:
    Apr 8, 2019
    Messages:
    146
    Likes Received:
    30
    Trophy Points:
    28
    Could the reverbs be expanded or approved? Yes. Are they bad? No, IMHO.

    Probably doesn't matter, but old firmware had a bug where the reverb settings needed to be cranked up. If you load presets from that firmware into the latest firmware, you'll need to turn the reverb down.

    FYI, I always need to tweak the reverb based upon the room and equipment I use with the AA.
     
    Last edited: Jun 28, 2020

Share This Page

Share